View PCF85063BTL_6168226.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the PCF85063BTL is a cmos 1 real-time clock (rtc) and calendar optimized for low power consumption. an offset register allows fine-tuning of the clock. all addresses and data are transferred serially via a serial peripheral interface (spi-bus) with a maximum data rate of 6.25 mbit/s. the register address is incremented automatically after each written or read data byte. 2. features and benefits ? provides year, month, day, weekday, hours, minutes, and seconds based on a 32.768 khz quartz crystal ? clock operating voltage: 0.9 v to 5.5 v ? low current; typical 0.22 ? aat v dd = 3.3 v and t amb =25 ? c ? 3 line spi-bus with a maximum data rate of 7 mbit/s ? programmable clock output for periphe ral devices (32.768 khz, 16.384 khz, 8.192 khz, 4.096 khz, 2.048 khz, 1.024 khz, and 1 hz) ? selectable integrated oscilla tor load capacitors for c l =7pf or c l = 12.5 pf ? alarm function ? countdown timer ? minute and half minute interrupt ? internal power-on reset (por) ? programmable offset register for frequency adjustment 3. applications ? digital still camera ? digital video camera ? printers ? copy machines ? mobile equipment ? battery powered devices PCF85063BTL tiny real-time clock/cale ndar with alarm function and spi-bus rev. 2 ? 15 april 2013 product data sheet 1. the definition of the abbreviations and acronyms used in this data sheet can be found in section 19 .
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 2 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 4. ordering information 4.1 ordering options 5. marking 6. block diagram table 1. ordering information type number package name description version PCF85063BTL hxson10 plastic thermal enhanced extremely thin small outline package; no leads; 10 terminals; body 2.6 ? 2.6 ? 0.5 mm sot1197-1 table 2. ordering options product type number ic revision sales item (12nc) delivery form PCF85063BTL/1 1 935299022118 tape and reel, 13 inch table 3. marking codes product type number marking code PCF85063BTL 063b fig 1. block diagram of PCF85063BTL

PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 3 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 7. pinning information 7.1 pinning 7.2 pin description [1] the die paddle (exposed pad) is connected to v ss and should be electrically isolated. for mechanical details, see figure 27 . fig 2. pin configuration for hxson10 (PCF85063BTL)
!"##$!%&"'
() ( * + , -
. / table 4. pin description symbol pin type description osci 1 input oscillator input osco 2 output oscillator output clkoe 3 input clkout enable or disable pin; enable is active high int 4 output interrupt output (open-drain) vss 5 [1] supply ground supply voltage ce 6 input chip enable scl 7 input serial clock input sdio 8 input/output serial data input and output clkout 9 output clock output (push-pull) vdd 10 supply supply voltage
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 4 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8. functional description the PCF85063BTL contains 18 8-bit registers with an auto-incrementing register address, an on-chip 32.768 khz oscillator with integr ated capacitors, a freq uency divider which provides the source clock for the real-time clock (rtc) and calender, and spi-bus with a maximum data rate of 6.25 mbit/s. the built-in address register will increment automatically after ea ch read or write of a data byte up to the register 11h. after register 11h, the auto-i ncrementing will wrap around to address 00h (see figure 3 ). all registers (see ta b l e 5 ) are designed as addressable 8-bit parallel registers although not all bits are implemented. the first two registers (memory address 00h and 01h) are used as control and status register. the regi ster at address 02h is an offset register allowing the fine-tuning of the clock; and at 03h is a free ram byte. the addresses 04h through 0ah are used as counters for the clock function (seconds up to years counters). address locations 0bh through 0fh contain alarm registers which define the conditions for an alarm. the registers at 10h and 11h are for the timer function. the seconds, minutes, hours, days, months, and years as well as the corresponding alarm registers are all coded in binary coded decimal (bcd) format. when one of the rtc registers is written or read, the contents of all time counters are frozen. therefore, faulty writing or reading of the clock and ca lendar during a carry condition is prevented. fig 3. handling address registers 00" "1& #" ))2 3#$&4"5"# '!$30 )(2 )2 )2 666 )2 ()2 ((2
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 5 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.1 registers organization table 5. registers overview bit positions labeled as - are not implemented. after reset, all registers are set according to table 8 on page 9 . address register name bit reference 7 6 5 4 3 2 1 0 control and status registers 00h control_1 ext_test - stop sr - cie 12_24 cap_sel section 8.2.1 01h control_2 aie af mi hmi tf cof[2:0] section 8.2.2 02h offset mode offset[6:0] section 8.2.3 03h ram_byte b[7:0] section 8.2.4 time and date registers 04h seconds os seconds (0 to 59) section 8.3.1 05h minutes - minutes (0 to 59) section 8.3.2 06h hours - - ampm hours (1 to 12) in 12 hour mode section 8.3.3 hours (0 to 23) in 24 hour mode 07h days - - days (1 to 31) section 8.3.4 08h weekdays - - - - - weekdays (0 to 6) section 8.3.5 09h months - - - months (1 to 12) section 8.3.6 0ah years years (0 to 99) section 8.3.7 alarm registers 0bh second_alarm aen_s second_alarm (0 to 59) section 8.5.1 0ch minute_alarm aen_m minute_alarm (0 to 59) section 8.5.2 0dh hour_alarm aen_h - ampm hour_alarm (1 to 12) in 12 hour mode section 8.5.3 hour_alarm (0 to 23) in 24 hour mode 0eh day_alarm aen_d - day_alarm (1 to 31) section 8.5.4 0fh weekday_alarm aen_w - - - - weekday_alarm (0 to 6) section 8.5.5 timer registers 10h timer_value t[7:0] section 8.6.1 11h timer_mode - - - tcf[1:0] te tie ti_tp section 8.6.2
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 6 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2 control registers 8.2.1 register control_1 [1] default value. [2] for a software reset, 01011000 (58h) must be sent to register control_1 (see section 8.2.1.3 ). 8.2.1.1 ext_test: external clock test mode a test mode is available which allows for on-boar d testing. in this mode, it is possible to set up test conditions and control the operation of the rtc. the test mode is entered by setting bit ext_test in register control_1. then pin clkout becomes an input. the test mode replaces the internal clock signal with the signal applied to pin clkout. the signal applied to pin clkout should have a minimum pulse width of 300 ns and a maximum period of 1000 ns. the internal cl ock, now sourced from clkout, is divided down to 1 hz by a 2 6 divide chain called a prescaler. the prescaler can be set into a known state by using bit stop. when bit stop is set, the prescaler is reset to 0. (stop must be cleared before the prescaler can operate again.) table 6. control_1 - control and status re gister 1 (address 00h) bit description bit symbol value description reference 7 ext_test external clock test mode section 8.2.1.1 0 [1] normal mode 1 external clock test mode 6 - 0 unused - 5stop stop bit section 8.2.1.2 0 [1] rtc clock runs 1 rtc clock is stopped; all rtc divider chain flip-flops are asynchronously set logic 0 4sr software reset section 8.2.1.3 0 [1] no software reset 1 initiate software reset [2] ; this bit always returns a 0 when read 3 - 0 unused - 2cie correction interrupt enable section 8.2.3 0 [1] no correction interrupt generated 1 interrupt pulses are generated at every correction cycle 1 12_24 12 or 24 hour mode section 8.3.3 section 8.5.3 0 [1] 24 hour mode is selected 1 12 hour mode is selected 0 cap_sel internal oscillator capacitor selection for quartz crystals with a corresponding load capacitance - 0 [1] 7 pf 1 12.5 pf
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 7 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus from a stop condition, the fi rst 1 second increment will take place after 32 positive edges on pin clkout. thereafter, every 64 pos itive edges cause a 1 second increment. remark: entry into test mode is not synchroni zed to the internal 64 hz clock. when entering the test mode, no assumption as to the state of the prescaler can be made. operation example: 1. set ext_test test mode (regis ter control_1, bit ext_test = 1). 2. set stop (register control_1, bit stop = 1). 3. clear stop (register control_1, bit stop = 0). 4. set time registers to desired value. 5. apply 32 clock pulses to pin clkout. 6. read time registers to see the first change. 7. apply 64 clock pulses to pin clkout. 8. read time registers to see the second change. repeat 7 and 8 for additional increments. 8.2.1.2 stop: stop bit function the function of the stop bit (see figure 4 ) is to allow for accurate starting of the time circuits. the stop bit function causes the upper part of the prescaler (f 2 to f 14 ) to be held in reset and thus no 1 hz ticks are gene rated. it also stops the output of clock frequencies lower than 8 khz on pin clkout. the time circuits can then be set and do not increment until the stop bit is released (see figure 5 and ta b l e 7 ). fig 4. stop bit functional diagram "##&1#2" 781 ) ,.+ (.+- +(* -)*. (#&4 ( ( (-
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 8 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus [1] f 0 is clocked at 32.768 khz. the lower two stages of the prescaler (f 0 and f 1 ) are not reset. and because the spi-bus is asynchronous to the crystal oscillator, the accuracy of restarting the time circuits is between zero and one 8.192 khz cycle (see figure 5 ). the first increment of the time circuits is between 0.507813 s and 0.507935 s after stop bit is released. the uncertainty is caused by the prescaler bits f 0 and f 1 not being reset (see table 7 ) and the unknown state of the 32 khz clock. table 7. first increment of time circuits after stop bit release bit prescaler bits [1] 1hz tick time comment stop f 0 f 1 -f 2 to f 14 hh:mm:ss clock is running normally 0 01-0 0001 1101 0100 12:45:12 prescaler counting normally stop bit is activated by user. f 0 f 1 are not reset and values cannot be predicted externally 1 xx-0 0000 0000 0000 12:45:12 prescaler is reset; time circuits are frozen new time is set by user 1 xx-0 0000 0000 0000 08:00:00 prescaler is reset; time circuits are frozen stop bit is released by user 0 xx-0 0000 0000 0000 08:00:00 prescaler is now running xx-1 0000 0000 0000 08:00:00 - xx-0 1000 0000 0000 08:00:00 - xx-1 1000 0000 0000 08:00:00 - : :: 11-1 1111 1111 1110 08:00:00 - 00-0 0000 0000 0001 08:00:01 0 to 1 transition of f 14 increments the time circuits 10-0 0000 0000 0001 08:00:01 - : :: 11-1 1111 1111 1111 08:00:01 - 00-0 0000 0000 0000 08:00:01 - 10-0 0000 0000 0000 08:00:01 - : :: 11-1 1111 1111 1110 08:00:01 - 00-0 0000 0000 0001 08:00:02 0 to 1 transition of f 14 increments the time circuits
(6) ))))) )6 /),+( #$ )6/ ),*/ fig 5. stop bit release timing )9 #$(9 +(* #$!"8" "0
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 9 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2.1.3 software reset a reset is automatically generated at power-o n. a reset can also be initiated with the software reset command. software reset command means setting bits 6, 4, and 3 in register control_1 (00h) logic 1 and all other bits logic 0 by sending the bit sequence 01011000 (58h), see figure 6 . in reset state all regist ers are set according to ta b l e 8 and the address pointer returns to address 00h. (1) when ce is inactive, the interface is reset. fig 6. software reset command table 8. registers reset values address register name bit 7 6 5 4 3 2 1 0 00h control_1 00000000 01h control_2 00000000 02h offset 00000000 03h ram_byte 00000000 04h seconds 10000000 05h minutes 00000000 06h hours 00000000 07h days 00000001 08h weekdays 00000110 09h months 00000001 0ah years 00000000 0bh second_alarm 1 0000000 0chminute_alarm 10000000 0dhhour_alarm 10000000 0eh day_alarm 10000000 0fh weekday_alarm10000000 10h timer_value 00000000 11h timer_mode 00011000 :, ) :. ) :/ ( :- ) : ) : ) :( ) :) ) :, ) :. ( :/ ) :- ( : ( : ) :( ) :) ) ;(< &#"8 " "# &18 = 00)) > $7#'"" "#/+ >
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 10 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus the PCF85063BTL resets to: time ? 00:00:00 date ? 20000101 weekday ? saturday 8.2.2 register control_2 [1] default value. table 9. control_2 - control and status re gister 2 (address 01h) bit description bit symbol value description reference 7aie alarm interrupt section 8.2.2.1 section 8.5.6 0 [1] disabled 1 enabled 6af alarm flag section 8.2.2.1 section 8.5.6 0 [1] read: alarm flag inactive write: alarm flag is cleared 1 read: alarm flag active write: alarm flag remains unchanged 5mi minute interrupt section 8.2.2.2 section 8.2.2.3 0 [1] disabled 1 enabled 4hmi half minute interrupt section 8.2.2.2 section 8.2.2.3 0 [1] disabled 1 enabled 3tf timer flag section 8.2.2.1 section 8.2.2.3 section 8.6.3 0 [1] no timer interrupt generated 1 flag set when timer interrupt generated 2 to 0 cof[2:0] see ta b l e 11 clkout control section 8.2.2.4
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 11 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2.2.1 alarm interrupt aie: this bit activates or deactivates the generat ion of an interrupt when af is asserted, respectively. af: when an alarm occurs, af is set logic 1. th is bit maintains its value until overwritten by command. to prevent one flag being overwri tten while clearing another, a logic and is performed during a write access. 8.2.2.2 mi and hmi: minute and half minute interrupt the minute interrupt (bit mi) and half minute in terrupt (bit hmi) are pre-defined timers for generating interrupt pulses on pin int ; see figure 8 . the timers are running in sync with the seconds counter (see table 19 on page 18 ). when starting mi, the first in terrupt will be generated after 1 second to 59 seconds. when starting hmi, the first in terrupt will be generated after 1 second to 29 seconds. subsequent periods do not have such a delay. the timers can be enabled independently from one another. however, a minute interrupt enabled on top of a half minute interrupt is not distinguishable. when aie bit is disabled, pin int remains high-impedance. fig 7. interrupt scheme ) ( "?5!8" @a 7$5&#"74"@ 48" 7$5&#"74"@ 48" $77 "#4&43&#@ 00= 3: #4# !38 " 7$5&#"74"@ "# #$&#"74"@ "0 #$&#"74"@ "0 a ( aa b @a "#85 781c a aa ) (
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 12 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus the duration of the timer is affected by the register offset (see section 8.2.3 ). only when offset[6:0] has the value 00h the periods are consistent. 8.2.2.3 tf: timer flag the timer flag (bit tf) is set logic 1 on the firs t trigger of mi, hmi, or the countdown timer. the purpose of the flag is to allow the controlling system to interrogat e what caused the interrupt: timer or alarm. the flag can be read and cleared by command. the status of the timer flag tf can affect the int pulse generation depending on the setting of ti_tp (see section 8.6.2 ? register timer_mode ? on page 27 ): ? when ti_tp is set logic 1 ? an int pulse is generated independent of the status of the timer flag tf ? tf stays set until it is cleared ? tf does not affect int ? the countdown timer runs in a repetitive loop and keeps generating timed periods ? when ti_tp is set logic 0 ? the int generation follows the tf flag ? tf stays set until it is cleared ? if tf is not cleared before the next coming interrupt, no int is generated ? the countdown timer stops after the first countdown 8.2.2.4 cof[2:0]: clock output frequency a programmable square wave is available at pin clkout. operation is controlled by the cof[2:0] bits in the register control_2. fr equencies of 32.768 khz (default) down to 1 hz can be generated for use as a system clock, microcontroller clock, input to a charge pump, or for calibration of the oscillator. in this example, the tf flag is not cleared after an interrupt. fig 8. int example for mi table 10. effect of bits mi and hmi on int generation minute interrupt (bit mi) half minute inte rrupt (bit hmi) result 0 0 no interrupt generated 1 0 an interrupt every minute 0 1 an interrupt every 30 s 1 1 an interrupt every 30 s /+ "4$0 4$3#" 5&3#" 4$3#" '2"":8"0 '2"":8"0 /* /* (( )) )()) (
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 13 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus pin clkout is a push-pull output and enabled at power-on. clkout can be disabled by setting cof[2:0] to 111 or by setting clkoe low. when disabled, the clkout is low. the duty cycle of the selected clock is not c ontrolled. however, due to the nature of the clock generation, all are 50 : 50 except the 32.768 khz frequencies. the stop bit function can also affect the clkout signal, depending on the selected frequency. when the stop bit is set logic 1, the clkout pin generates a continuous low for those frequencies that can be stopped. for more details of the stop bit function, see section 8.2.1.2 . [1] duty cycle definition: % high-level time : % low-level time. [2] default value. [3] 1 hz clock pulses are affected by offset correction pulses. 8.2.3 register offset the PCF85063BTL incorporates an offset register (address 02h) which can be used to implement several functions, such as: ? accuracy tuning ? aging adjustment ? temperature compensation [1] default value. for mode = 0, each lsb introduces an offs et of 4.34 ppm. for mode = 1, each lsb introduces an offset of 4.069 ppm. the valu es of 4.34 ppm and 4.069 ppm are based on a nominal 32.768 khz clock. the offset value is coded in two?s complement giving a range of +63 lsb to ? 64 lsb. table 11. clkout frequency selection cof[2:0] clkout frequency (hz) typical duty cycle [1] effect of stop bit 000 [2] 32768 60 : 40 to 40 : 60 no effect 001 16384 50 : 50 no effect 010 8192 50 : 50 no effect 011 4096 50 : 50 clkout = low 100 2048 50 : 50 clkout = low 101 1024 50 : 50 clkout = low 110 1 [3] 50 : 50 clkout = low 111 clkout = low - - table 12. offset - offset register (address 02h) bit description bit symbol value description 7mode offset mode 0 [1] normal mode: offset is made once every two hours 1 course mode: offset is made every 4 minutes 6 to 0 offset[6:0] see ta b l e 1 3 offset value
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 14 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus [1] default value. the correction is made by adding or subtra cting clock correction pulses, thereby changing the period of a single second but not by changing the oscillator frequency. it is possible to monitor when correction pulses are applied. to enable correction interrupt generation, bit cie (register control_1) has to be set logic 1. at every correction cycle a pulse is generated on pin int . the pulse width depends on the correction mode. if multiple correction pulses are applied, an interrupt pulse is generated for each correction pulse applied. table 13. offset values offset[6:0] offset value in decimal offset value in ppm normal mode mode = 0 fast mode mode = 1 0111111 +63 +273.420 +256.347 0111110 +62 +269.080 +252.278 :: : : 0000010 +2 +8.680 +8.138 0000001 +1 +4.340 +4.069 0000000 [1] 00 [1] 0 [1] 1111111 ? 1 ? 4.340 ? 4.069 1111110 ? 2 ? 8.680 ? 8.138 :: : : 1000001 ? 63 ? 273.420 ? 256.347 1000000 ? 64 ? 277.760 ? 260.416
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 15 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2.3.1 correction when mode = 0 the correction is triggered once every two ho urs and then correction pulses are applied once per minute until the programmed correction values have been implemented. [1] the correction pulses on pin int are 1 64 s wide. in mode = 0, any timer or clock output using a frequency below 64 hz is affected by the clock correction (see ta b l e 1 5 ). table 14. correction pulses for mode = 0 correction value update every n th hour minute correction pulses on int per minute [1] +1 or ? 12 00 1 +2 or ? 2 2 00 and 01 1 +3 or ? 3 2 00, 01, and 02 1 :::: +59 or ? 59 2 00 to 58 1 +60 or ? 60 2 00 to 59 1 +61 or ? 61 2 00 to 59 1 2nd and next hour 00 1 +62 or ? 62 2 00 to 59 1 2nd and next hour 00 and 01 1 +63 or ? 63 02 00 to 59 1 2nd and next hour 00, 01, and 02 1 ? 64 02 00 to 59 1 2nd and next hour 00, 01, 02, and 03 1 table 15. effect of correction pu lses on frequencies for mode = 0 frequency (hz) effect of correction clkout 32768 no effect 16384 no effect 8192 no effect 4096 no effect 2048 no effect 1024 no effect 1affected timer source clock 4096 no effect 64 no effect 1affected 1 60 affected
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 16 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2.3.2 correction when mode = 1 the correction is triggered once every four minutes and then correction pulses are applied once per second up to a maximum of 60 pulse s. when correction values greater than 60 pulses are used, additional correction pulses are made in the 59 th second. clock correction is made more frequently in mode = 1; however, this can result in higher power consumption. [1] the correction pulses on pin int are 1 1024 s wide. for multiple pulses, they are repeated at an interval of 1 512 s. in mode = 1, any timer source clock using a frequency below 1.024 khz is also affected by the clock correction (see ta b l e 1 7 ). table 16. correction pulses for mode = 1 correction value update every n th minute second correction pulses on int per second [1] +1 or ? 12 00 1 +2 or ? 2 2 00 and 01 1 +3 or ? 3 2 00, 01, and 02 1 :::: +59 or ? 59 2 00 to 58 1 +60 or ? 60 2 00 to 59 1 +61 or ? 61 2 00 to 58 1 25 92 +62 or ? 62 2 00 to 58 1 25 93 +63 or ? 63 2 00 to 58 1 25 94 ? 64 2 00 to 58 1 25 95 table 17. effect of correction pu lses on frequencies for mode = 1 frequency (hz) effect of correction clkout 32768 no effect 16384 no effect 8192 no effect 4096 no effect 2048 no effect 1024 no effect 1affected timer source clock 4096 no effect 64 affected 1affected 1 60 affected
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 17 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2.3.3 offset calibration workflow the calibration offset has to be calculated based on the time. figure 9 shows the workflow how the offset register values can be calculated: fig 9. offset calibratio n calculation workflow " 3"#2"7"d3"4e$!& @ 7 5" $%"##$#&5"@ # 5" f(=7 5" 8438#"#2"0&77""4"#$#2"&0"8 !"&$0$7(=,.+6))@ 5" f(=,.+# 5" 8438#"#2"!!50"%&#&$4$5!"0 #$#2"5" 3"0%83"@ !!5 f())))))g 5" =# 5" 8438#"#2"$77 "#"1& #"%83"@ $0"f);8$'!$'"<@ 77 "#%83"f !!5 =-6- $0"f(;7 #4$"4#&$< 77 "#%83"f !!5 =-6).* 5!8"48438#&$@ ,.+6-+ )6/(,((9 )6)))--,9 (-6.-+!!5 6,/ 4$"4#&$!38 " """0"0 6.)) -4$"4#&$!38 " """0"0
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 18 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.2.4 register ram_byte the PCF85063BTL provides a free ram byte, which can be used for any purpose, for example, status byte of the system. [1] default value. 8.3 time and date registers most of the registers are coded in the bcd format to simplify application use. 8.3.1 register seconds [1] default value. with the offset calibration an accuracy of ? 2 ppm (0.5 ? offset per lsb) can be reached (see table 13 ). ? 1 ppm corresponds to a time deviation of 0.0864 seconds per day. (1) 3 correction pulses in mode = 0 correspond to ? 13.02 ppm. (2) 4 correction pulses in mode = 1 correspond to ? 16.276 ppm. (3) reachable accuracy zone. fig 10. result of offset calibration ) - . + () ( (- (. . - ;< ;< ;(< 5" 3"0=48438#"0 0"%&#&$(-6.-+!!5 0"%&#&$7#" 4$"4#&$& f) h(6.+!!5 0"%&#&$7#" 4$"4#&$& f( (6.+!!5 table 18. ram_byte - 8-bit ram regist er (address 03h) bit description bit symbol value description 7 to 0 b[7:0] 00000000 [1] to 11111111 ram content table 19. seconds - seconds register (address 04h) bit description bit symbol value place value description 7os oscillator stop 0 - clock integrity is guaranteed 1 [1] - clock integrity is not guaranteed; oscillator has stopped or has been interrupted 6to4 seconds 0 [1] to 5 ten?s place actual seconds coded in bcd format, see table 20 3 to 0 0 [1] to 9 unit place
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 19 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus [1] default value. 8.3.1.1 os flag: oscillator stop when the oscillator of the PCF85063BTL is stopped, the os flag is set. the oscillator can be stopped, for example, by connecting one of the oscilla tor pins osci or osco to ground. the oscillator is cons idered to be stopped during th e time between power-on and stable crystal resonance. this time can be in the range of 200 ms to 2 s depending on crystal type, temperature, and supply voltage. the flag remains set until cleared by command (see figure 11 ). if the flag cannot be cleared, then the oscillator is not running. this method can be used to monitor the oscillator and to determine if the supply volt age has reduced to the point where oscillation fails. table 20. seconds coded in bcd format seconds value in decimal upper-digit (ten?s place) digit (unit place) bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 00 [1] 0000000 01 0000001 02 0000010 : ::::::: 09 0001001 10 0010000 : ::::::: 58 1011000 59 1011001 fig 11. os flag # f(07814$#:"48""0
$ 4&88#&$ $ 4&88#&$$' #:8" 78148""0 :e $7#'" 781 "#'2" $ 4&88#&$ #$! 781 f(07814:"48""0
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 20 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.3.2 register minutes [1] default value. 8.3.3 register hours [1] hour mode is set by the 12_24 bit in register control_1. [2] default value. 8.3.4 register days [1] if the year counter contains a value, which is exac tly divisible by 4 (including the year 00), the PCF85063BTL compensates for leap y ears by adding a 29th day to february. [2] default value. [3] default value is 1. 8.3.5 register weekdays table 21. minutes - minutes register (address 05h) bit description bit symbol value place value description 7 - 0 - unused 6to4 minutes 0 [1] to 5 ten?s place actual minutes coded in bcd format 3 to 0 0 [1] to 9 unit place table 22. hours - hours register (address 06h) bit description bit symbol value place value description 7 to 6 - 00 - unused 12 hour mode [1] 5ampm am/pm indicator 0 [2] -a m 1- p m 4 hours 0 [2] to 1 ten?s place actual hours in 12 hour mode coded in bcd format 3to0 0 [2] to 9 unit place 24 hour mode [1] 5 to 4 hours 0 [2] to 2 ten?s place actual hours in 24 hour mode coded in bcd format 3to0 0 [2] to 9 unit place table 23. days - days register (address 07h) bit description bit symbol value place value description 7 to 6 - 00 - unused 5to4 days [1] 0 [2] to 3 ten?s place actual day coded in bcd format 3to0 0 [3] to 9 unit place table 24. weekdays - weekdays register (address 08h) bit description bit symbol value description 7 to 3 - 00000 unused 2to0 weekdays 0to6 actual weekday values, see ta b l e 2 5
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 21 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus [1] definition may be reassigned by the user. [2] default value. 8.3.6 register months [1] default value. table 25. weekday assignments day [1] bit 2 1 0 sunday 0 0 0 monday 0 0 1 tuesday 0 1 0 wednesday 0 1 1 thursday 1 0 0 friday 1 0 1 saturday [2] 110 table 26. months - months register (address 09h) bit description bit symbol value place value description 7 to 5 - 000 - unused 4 months 0 to 1 ten?s place actual month coded in bcd format, see table 27 3 to 0 0 to 9 unit place table 27. month assignments in bcd format month upper-digit (ten?s place) digit (unit place) bit 4 bit 3 bit 2 bit 1 bit 0 january [1] 00001 february 0 0 0 1 0 march 0 0 0 1 1 april00100 may00101 june00110 july00111 august01000 september 0 1 0 0 1 october10000 november10001 december10010
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 22 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.3.7 register years [1] default value. 8.4 setting and reading the time figure 12 shows the data flow and data dependencies starting from the 1 hz clock tick. during read/write operations, the time counting circuits (memory locations 04h through 0ah) are blocked. the blocking prevents ? faulty reading of the clock and calendar during a carry condition ? incrementing the time regist ers during the read cycle after this read/write access is completed, the time circuit is released again and any pending request to increment the time counte rs that occurred during the read/write access is serviced. a maximum of 1 request can be stored; therefore, all accesses must be completed within 1 second (see figure 13 ). table 28. years - years register (0ah) bit description bit symbol value place value description 7 to 4 years 0 [1] to 9 ten?s place actual year coded in bcd format 3to0 0 [1] to 9 unit place fig 12. data flow fo r the time function (#&4 (b-2$35$0"
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 23 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus because of this method, it is very important to make a read or write access in one go, that is, setting or reading seconds through to years should be made in one single access. failing to comply with this method could result in th e time becoming corrupted. as an example, if the time (seconds through to hours) is set in one access and then in a second access the date is set, it is possible that the time will increment between the two accesses. a similar problem exists when reading. a roll-over may occur between reads thus giving the minutes from one moment and the hours from the next. recommended method for reading the time: 1. send read command with register address pointing to 4 (seconds) by sending 04h 2. read seconds 3. read minutes 4. read hours 5. read days 6. read weekdays 7. read months 8. read years fig 13. access time for read/write operations 0#:3 42&!":8" #i(
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 24 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.5 alarm registers 8.5.1 register second_alarm [1] default value. 8.5.2 register minute_alarm [1] default value. 8.5.3 register hour_alarm [1] default value. [2] hour mode is set by the 12_24 bit in register control_1. table 29. second_alarm - second alarm register (address 0bh) bit description bit symbol value place value description 7 aen_s second alarm 0 - enabled 1 [1] - disabled 6 to 4 second_alarm 0 [1] to 5 ten?s place second alarm information coded in bcd format 3 to 0 0 [1] to 9 unit place table 30. minute_alarm - minute alarm register (address 0ch) bit description bit symbol value place value description 7 aen_m minute alarm 0 - enabled 1 [1] - disabled 6 to 4 minute_alarm 0 [1] to 5 ten?s place minute ala rm information coded in bcd format 3 to 0 0 [1] to 9 unit place table 31. hour_alarm - hour alarm regist er (address 0dh) bit description bit symbol value place value description 7 aen_h hour alarm 0 - enabled 1 [1] - disabled 6 - 0 - unused 12 hour mode [2] 5ampm am/pm indicator 0 [1] -a m 1- p m 4 hour_alarm 0 [1] to 1 ten?s place hour alarm information in 12 hour mode coded in bcd format 3to0 0 [1] to 9 unit place 24 hour mode [2] 5 to 4 hour_alarm 0 [1] to 2 ten?s place hour alarm information in 24 hour mode coded in bcd format 3to0 0 [1] to 9 unit place
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 25 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.5.4 register day_alarm [1] default value. 8.5.5 register weekday_alarm [1] default value. 8.5.6 alarm function by clearing the alarm enable bit (aen_x) of one or more of the alarm registers, the corresponding alarm condition(s) are active. when an alarm occurs, af is set logic 1. the asserted af can be used to generate an interrupt (int ). the af is cleared by command. the registers at addresses 0bh through 0fh contain alarm information. when one or more of these registers is loaded with second, minute, hour, day or weekday, and its corresponding aen_x is logic 0, then that information is compared with the current second, minute, hour, day, and weekday. when all enabled comparisons first match, the alarm flag (af in register control_2) is set logic 1. the generation of interrupts from the alarm func tion is controlled via bit aie. if bit aie is enabled, the int pin follows the condition of bit af. af remains set until cleared by command. once af has been clear ed, it will only be set again when the time increments to match the alarm condition once more. al arm registers which have their aen_x bit at logic 1 are ignored. table 32. day_alarm - day alarm register (address 0eh) bit description bit symbol value place value description 7 aen_d day alarm 0 - enabled 1 [1] - disabled 6 - 0 - unused 5 to 4 day_alarm 0 [1] to 3 ten?s place day alarm information coded in bcd format 3 to 0 0 [1] to 9 unit place table 33. weekday_alarm - weekday alarm re gister (address 0fh) bit description bit symbol value description 7 aen_w weekday alarm 0 enabled 1 [1] disabled 6 to 3 - 0 unused 2to0 weekday_alarm 0 [1] to 6 weekday alarm information coded in bcd format
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 26 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus (1) only when all enabled alarm settings are matching. it is only on increment to a matched case that the alarm flag is set. fig 14. alarm function block diagram b ( ) b f( "?5!8" f b f b "#85781 ;(< f b f b f 42"4$' &18
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 27 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 8.6 timer registers the 8-bit countdown timer at address 10h is controlled by the register timer_mode at address 11h. 8.6.1 register timer_value [1] default value. [2] countdown period in seconds: where t is the countdown value. 8.6.2 register timer_mode [1] default value. [2] how the setting of ti_tp and the timer flag tf can affect the int pulse generation is explained in section 8.2.2.3 on page 12 . 8.6.3 timer functions the timer has four selectable source clocks allowing for countdown periods in the range from 244 ? s to 4 hours 15 min. for periods longer than 4 hours, the al arm function can be used. table 34. timer_value - timer value regi ster (address 10h) bit description bit symbol value description 7to0 t[7:0] 0h [1] to ffh countdown timer value [2] countdownperiod t sourceclockfrequency -------------------------------------------------------------- - = table 35. timer_mode - timer control re gister (address 11h) bit description bit symbol value description 7 to 5 - 000 unused 4 to 3 tcf[1:0] timer clock frequency 00 4.096 khz timer source clock 01 64 hz timer source clock 10 1 hz timer source clock 11 [1] 1 60 hz timer source clock 2te timer enable 0 [1] timer is disabled 1 timer is enabled 1tie timer interrupt enable 0 [1] no interrupt generated from timer 1 interrupt generated from timer 0ti_tp [2] timer interrupt mode 0 [1] interrupt follows timer flag 1 interrupt generates a pulse
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 28 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus [1] when not in use, tcf[1:0] must be set to 1 60 hz for power saving. [2] time periods can be affected by correction pulses. remark: note that all timings which are genera ted from the 32.768 khz oscillator are based on the assumption that there is 0 ppm deviation. devi ation in oscillator frequency results in deviation in timings. this is not applicable to interface timing. the timer counts down from a software-loaded 8-bit binary value, t[7:0], in register timer_value. loading the counter with 0 stops the timer. values from 1 to 255 are valid. when the counter decrements from 1, the timer fl ag (bit tf in register control_2) is set and the counter automatically re-loads and starts the next timer period. if a new value of t is written before the end of the current timer period, then this value takes immediate effect. nxp does not recommend changing t without first disabling the counter by setting bit te logic 0. the update of t is asynchronous to the timer clock. therefore changing it without setting bit te logic 0 may result in a corrupted value loaded into the countdown counter. this results in an undetermined countdown period for the first period. the countdown value t will, however, be correctly st ored and correctly loaded on subsequent timer periods. table 36. timer clock frequency and timer durations tcf[1:0] timer source clock frequency [1] delay minimum timer duration t= 1 maximum timer duration t=255 00 4.096 khz 244 ? s 62.256 ms 01 64 hz 15.625 ms 3.984 s 10 1 hz [2] 1 s 255 s 11 1 60 hz [2] 60 s 4 hours 15 min in this example, it is assumed that the ti mer flag is cleared before the next countdown period expires and that the pin int is set to pulsed mode. fig 15. general countdown timer behavior )?? ) )( ) ) )( ) ) )( ) ) ?? 4$3#0$'%83"c #&5" $34"48$4 4$3#0$'4$3#" 03#&$$77& ##&5"!"&$07#" ":8"5e1"7$5(#$h(
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 29 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus when the tie flag is set, an interrupt signal on int is generated if this mode is enabled. see section 8.2.2 for details on how the interrupt can be controlled. when starting the timer for the first time, the first period has an uncertainty. the uncertainty is a result of the enable instru ction being generated from the interface clock which is asynchronous from the timer source clock. subsequent timer periods do not have such delay. the amount of delay for the firs t timer period depends on the chosen source clock, see ta b l e 3 7 . at the end of every countdown, the timer sets the countdown timer flag (bit tf in register control_2). bit tf can only be cleared by co mmand. the asserted bit tf can be used to generate an interrupt at pin int . the interrupt may be generated as a pulsed signal every countdown period or as a permanently active si gnal which follows the condition of bit tf. bit ti_tp is used to control this mode selection and the interrupt output may be disabled with bit tie, see ta b l e 3 5 and figure 15 . when reading the timer, the current countdown value is returned and not the initial value t. since it is not possible to freeze th e countdown timer counter during read back, it is recommended to read the register twice and check for consistent results. timer source clock frequency selection of 1 hz and 1 60 hz is affected by the offset register. the duration of a program period varies according to when the offset is initiated. for example, if a 100 s timer is set using the 1 hz clock as source, then some 100 s periods will contain correction pulses and therefore be longer or shorter depending on the setting of the offset register. see section 8.2.3 to understand the operation of the offset register. 8.6.3.1 countdown timer interrupts the pulse generator for the countdown timer interrupt uses an internal clock and is dependent on the selected source clock fo r the countdown timer and on the countdown value t. as a consequence, the width of the interrupt pulse varies (see ta b l e 3 8 ). [1] t = loaded countdown value. timer stops when t = 0. table 37. first period delay for timer counter value t timer source clock minimum timer period maximum timer period 4.096 khz t t + 1 64 hz t t + 1 1 hz 1 60 hz t1 ? ?? -------------- + t 1 64 hz -------------- + t1 ? ?? -------------- + t 1 64 hz -------------- + table 38. int operation tf and int become active simultaneously. source clock (hz) int period (s) t=1 [1] t>1 [1] 4096 1 8192 1 4096 64 1 128 1 64 1 1 64 1 64 1 60 1 64 1 64
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 30 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 9. characteristics of the spi-bus interface data transfer to and from the device is made via a 3-wire spi-bus (see table 39 ). the chip enable signal is used to identify the transmitted data. each data transfer is a byte, with the most significant bit (msb) sent first (see figure 16 ). the transmission is controlled by the active high chip enable signal ce. the first byte transmitted is the command byte. subsequent bytes are either data to be written or data to be read. data is sampled on the rising edge of the clock and transferred internally on the falling edge. the command byte defines the address of th e first register to be accessed and the read/write mode. the address counter will auto increment after every access and will roll over to zero after the last register is accessed (see figure 3 ). the (r/w ) bit defines whether the following bytes are read or write information. in figure 17 , the register seconds is set to 45 sec onds and the register minutes is set to 10 minutes. in figure 18 , the months and years registers are read. table 39. serial interface symbol function description ce chip enable input when low, the interface is reset; pull-down resistor included; active input may be higher than v dd , but may not be wired permanently high scl serial clock input when ce is low, this input may float; input may be higher than v dd sdio serial data input and output input when ce is low, input may float; input may be higher than v dd ; input data is sampled on the rising edge of scl output push-pull output; drives from v ss to v dd ; output data is changed on the falling edge of scl; is high-impedance when not driving fig 16. data transfer overview table 40. command byte definition bit symbol value description 7r/w data read or data write selection 0 write data 1 read data 6to5 sa 01 subaddress ; other codes will cause the device to ignore data transfer 4to0 ra 0h to 11h register address range ; other addresses will be ignored 0#:3 42&!":8"
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 31 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus fig 17. spi-bus write example
:, ) :) ) :( ) : ( : ) :- ) :/ ( :. ) :, ) :. ( :/ ) :- ) : ) : ( :( ) :) ( :, ) :. ) :/ ) :- ( : ) : ) :( ) :) ) "4$0 0#-/ 5&3#" 0#() = 00)- > )- ) ) ?? 0 0" 4$ 3#" fig 18. spi-bus read example :, ) :) ( :( ) : ) : ( :- ) :/ ( :. ) :, ( :. ) :/ ) :- ( : ) : ) :( ) :) ( :, ) :. ) :/ ) :- ) : ) : ( :( ( :) ) 5$#2 0#(( e" 0#). = 00)* > )* )+ ), ?? 0 0" 4$ 3#"
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 32 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 10. internal circuitry 11. limiting values [1] pass level; human body model (hbm) according to ref. 7 ? jesd22-a114 ? . [2] pass level; charged-device model (cdm), according to ref. 8 ? jesd22-c101 ? . [3] pass level; latch-up testing, according to ref. 9 ? jesd78 ? at maximum ambient temperature (t amb(max) ). [4] according to the store and transport requirements (see ref. 12 ? um10569 ? ) the devices have to be stored at a temperature of +8 ? c to +45 ? c and a humidity of 25 % to 75 %. fig 19. device diode protection diagram of PCF85063BTL

table 41. limiting values in accordance with the absolute maximum rating system (iec 60134). symbol parameter conditions min max unit v dd supply voltage ? 0.5 +6.5 v i dd supply current ? 50 +50 ma v i input voltage on pins scl, sdio, osci ? 0.5 +6.5 v v o output voltage ? 0.5 +6.5 v i i input current at any input ? 10 +10 ma i o output current at any output ? 10 +10 ma p tot total power dissipation - 300 mw v esd electrostatic discharge voltage hbm [1] - ? 5000 v cdm [2] - ? 2000 v i lu latch-up current [3] -200ma t stg storage temperature [4] ? 65 +150 ?c t amb ambient temperature operating device ? 40 +85 ?c
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 33 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 12. characteristics table 42. static characteristics v dd = 0.9 v to 5.5 v; v ss =0v; t amb = ? 40 ? c to +85 ? c; f osc = 32.768 khz; quartz r s =60k ? ; c l = 7 pf; unless otherwise specified. symbol parameter conditions min typ max unit supplies v dd supply voltage interface inactive; f scl =0mhz [1] 0.9- 5.5v interface active; f scl =1mhz [1] 1.8- 5.5v i dd supply current clkout disabled; v dd =3.3v [2] interface inactive; f scl =0hz t amb =25 ?c - 220 450 na t amb =50 ?c [3] - 250 500 na t amb =85 ?c - 470 600 na interface active; f scl =1mhz -45200 ? a inputs v i input voltage v ss -5 . 5v v il low-level input voltage v ss -0 . 3 v dd v v ih high-level input voltage 0.7v dd -v dd v i li input leakage current v i =v ss or v dd -0- ? a post esd event ? 0.15 - +0.15 ? a c i input capacitance on pins sdio, scl, ce, clkoe [4] --7p f outputs v oh high-level output voltage on pins sdio, clkout 0.8v dd -v dd v v ol low-level output voltage on pins sdio, int , clkout v ss -0 . 2 v dd v i oh high-level output current output source current; v oh = 2.9 v; v dd = 3.3 v on pin sdio 2 5 - ma on pin clkout 1 3 - ma i ol low-level output current output sink current; v ol =0.4v; v dd =3.3v on pins sdio, int 26- ma on pin clkout 1 3 - ma
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 34 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus [1] for reliable oscillator start at power-on: v dd =v dd(po)sit min+0.3v. [2] timer source clock = 1 60 hz, level of pins ce, sdio, and scl is v dd or v ss . [3] tested on sample basis. [4] implicit by design. [5] integrated load capacitance, c l(itg) , is a calculation of c osci and c osco in series: . oscillator ? f osc /f osc relative oscilla tor frequency variation ? v dd =200mv; t amb =25 ?c - 0.075 - ppm c l(itg) integrated load capacitance on pins osco, osci [5] c l = 7 pf 4.2 7 9.8 pf c l = 12.5 pf 7.5 12.5 17.5 pf r s series resistance - - 100 k ? table 42. static characteristics ?continued v dd = 0.9 v to 5.5 v; v ss =0v; t amb = ? ? ? ? symbol parameter conditions min typ max unit c litg ?? ? ?? ?? ------------------------------------------- - = t amb =25 ? c; clkout disabled. (1) v dd =5.0v. (2) v dd =3.3v. fig 20. typical i dd with respect to f scl ) ())) ))) ))) -))) /))) .))) ) )) -)) .)) +)) 7 ;< ;9< ;9< ;9< ;(< ;<
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 35 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus c l(itg) = 7 pf; clkout disabled. (1) v dd =5.5v. (2) v dd =3.3v. c l(itg) = 12.5 pf; clkout disabled. (1) v dd =5.5v. (2) v dd =3.3v. fig 21. typical i dd as a function of temperature /) ) () () ) /) ,) *) ) )) -)) .)) +)) "5!"#3";j< ;< ;< ;< ;(< ;< /) ) () () ) /) ,) *) ) )) -)) .)) +)) ())) "5!"#3";j< ;< ;< ;< ;(< ;<
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 36 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus t amb =25 ? c; f clkout = 32768 hz. (1) 47 pf clkout load. (2) 22 pf clkout load. t amb =25 ? c; clkout disabled. (1) c l(itg) = 12.5 pf. (2) c l(itg) =7pf. fig 22. typical i dd with respect to v dd ) ( - / . ) - . + () (
;
< ;9< ;9< ;9< ;(< ;(< ;(< ;< ;< ;< ) ( - / . ) ()) )) )) -)) /))
;
< ;< ;< ;< ;(< ;<
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 37 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus v dd = 3.3 v; clkout disabled. (1) c l(itg) = 12.5 pf; 50 ? c; maximum value. (2) c l(itg) =7pf; 50 ? c; maximum value. (3) c l(itg) = 12.5 pf; 25 ? c; typical value. (4) c l(itg) =7pf; 25 ? c; typical value. fig 23. i dd with respect to quartz r s t amb =25 ? c. (1) c l(itg) =7pf. (2) c l(itg) = 12.5 pf. fig 24. oscillator frequency variation with respect to v dd ) ) -) /) .) ,) +) *) ()) ) )) -)) .)) +)) ;k< ;< ;< ;< ;-< ;-< ;-< ;< ;< ;< ;< ;< ;< ;(< ;(< ;(< ) ( - / . (6/ ) (6/
;
< l7 l7 $ 4 $ 4 l7 $ 4 ;!!5< ;!!5< ;!!5< ;(< ;<
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 38 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus table 43. spi-bus characteristics v dd = 1.8 v to 5.5 v; v ss =0v; t amb = ? 40 ? c to +85 ? c; f osc = 32.768 khz; quartz r s =60k ? ; c l = 7 pf; unless otherwise specified. all timing values are valid within the operat ing supply voltage and temperature range and referenced to v il and v ih with an input voltage swing of v ss to v dd . symbol parameter conditions v dd = 1.8v to 3.3v v dd > 3.3v to 5.5v unit min max min max f scl scl clock frequency - 5 - 7 mhz t scl scl time 140 - 140 - ns t clk(h) clock high time 80 - 80 - ns t clk(l) clock low time 110 - 60 - ns t r rise time for scl signal - 100 - 50 ns t f fall time for scl signal - 100 - 50 ns t su(ce) ce set-up time 15 - 15 - ns t h(ce) ce hold time 10 - 10 - ns t rec(ce) ce recovery time 50 - 50 - ns t w(ce) ce pulse width measured after valid subaddress is received - 0.99 - 0.99 s t su set-up time set-up time for sdio data 5- 5- ns t h hold time hold time for sdio data 50 - 20 - ns t d(r)sdo sdo read delay time bus load = 50 pf - 110 - 60 ns t dis(sdo) sdo disable time no load value; bus will be held up by bus capacitance; use rc time constant with application values - 50 - 50 ns t t(sdi-sdo) transition time from sdi to sdo to avoid bus conflict; on pin sdio 0- 0- ns
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 39 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus fig 25. spi-bus timing 001aai554 r/w sa2 ra0 b7 b6 b0 b7 b6 b0 b0 b6 b7 sdi sdo sdo hi z hi z sdi scl ce write read t w(ce) 80% 20% t clk(l) t f t h(ce) t rec(ce) t dis(sdo) t d(r)sdo t t(sdi-sdo) t r t h t su t clk(h) t scl t su(ce)
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 40 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 13. application information a 1 farad super capacitor combined with a low v f diode can be used as a standby or back-up supply. with the rtc in its minimum power confi guration that is, timer off and clkout off, the rtc may operate for weeks. (1) if the clock signal (pin clkout) is required in power-down mode, pin clkoe has to be connected to the cathode side of the diode. (2) r1 limits the inrush current to the super capacitor at power-on. fig 26. application diagram for PCF85063BTL
=

( ( ;(< ;< ())

PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 41 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 14. package outline fig 27. package outline sot1197-1 (hxson10) of PCF85063BTL references outline version european projection issue date iec jedec jeita sot1197-1 - - - - - - - - - sot1197-1_po 11-01-20 12-09-16 unit (1) mm max nom min 0.5 0.05 0.00 0.30 0.25 0.20 2.7 2.6 2.5 2.20 2.15 2.10 2.7 2.6 2.5 0.5 2 0.40 0.35 0.30 0.05 a dimensions note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. dfn2626-10: plastic thermal enhanced extremely thin small outline package; no leads; 10 terminals; body 2.6 x 2.6 x 0.5 mm sot1197-1 a 1 a 3 0.127 bdd h ee h 1.30 1.25 1.20 ee 1 k 0.2 lv 0.1 w 0.05 y 0.05 y 1 0 1 2 mm scale c y c y 1 x d e b a terminal 1 index area detail x a a 1 a 3 d h e h k l b e 1 e ac b v c w terminal 1 index area 5 1 6 10
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 42 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 15. handling information all input and output pins are protected ag ainst electrostatic discharge (esd) under normal handling. when handling metal-oxide semiconductor (mos) devices ensure that all normal precautions are taken as described in jesd625-a , iec 61340-5 or equivalent standards. 16. packing information 16.1 tape and reel information fig 28. tape and reel details for PCF85063BTL table 44. carrier tape dimensions of PCF85063BTL symbol description value unit compartments a0 pocket width in x direction 2.9 mm b0 pocket width in y direction 2.9 mm k0 pocket depth 0.8 mm p1 pocket hole pitch 4 mm d1 pocket hole diameter 1 mm overall dimensions w tape width 8 mm d0 sprocket hole diameter 1.5 mm p0 sprocket hole pitch 4 mm
0&"4#&$$77""0
) ) ( ) ) m) m( &1&80&5" &$ "&556 &13"$#0'#$ 48"6 !&(
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 43 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 17. soldering of smd packages this text provides a very brief insight into a complex technology. a more in-depth account of soldering ics can be found in application note an10365 ?surface mount reflow soldering description? . 17.1 introduction to soldering soldering is one of the most common methods through which packages are attached to printed circuit boards (pcbs), to form electr ical circuits. the soldered joint provides both the mechanical and the electrical connection. th ere is no single sold ering method that is ideal for all ic packages. wave soldering is often preferred when through-hole and surface mount devices (smds) are mixed on one printed wiring board; however, it is not suitable for fine pitch smds. reflow soldering is ideal for the small pitches and high densities that come with increased miniaturization. 17.2 wave and reflow soldering wave soldering is a joining technology in which the joints are made by solder coming from a standing wave of liquid solder. the wave soldering process is suitable for the following: ? through-hole components ? leaded or leadless smds, which are glued to the surface of the printed circuit board not all smds can be wave soldered. packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. also, leaded smds with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased pr obability of bridging. the reflow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature profile. leaded packages, packages with solder balls, and leadless packages are all reflow solderable. key characteristics in both wave and reflow soldering are: ? board specifications, in cluding the board finish , solder masks and vias ? package footprints, including solder thieves and orientation ? the moisture sensitivit y level of the packages ? package placement ? inspection and repair ? lead-free soldering versus snpb soldering 17.3 wave soldering key characteristics in wave soldering are: ? process issues, such as application of adhe sive and flux, clinching of leads, board transport, the solder wave parameters, and the time during which components are exposed to the wave ? solder bath specifications, including temperature and impurities
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 44 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 17.4 reflow soldering key characteristics in reflow soldering are: ? lead-free versus snpb solderi ng; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see figure 29 ) than a snpb process, thus reducing the process window ? solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board ? reflow temperature profile; this profile includ es preheat, reflow (in which the board is heated to the peak temperature) and cooling down. it is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). in addition, the peak temperature must be low enough that the packages and/or boards are not damaged. the peak temperature of the package depends on package thickness and volume and is classified in accordance with ta b l e 4 5 and 46 moisture sensitivity precautions, as indicat ed on the packing, must be respected at all times. studies have shown that small packages reach higher temperatures during reflow soldering, see figure 29 . table 45. snpb eutectic process (from j-std-020d) package thickness (mm) package reflow temperature ( ?c) volume (mm 3 ) < 350 ? 350 < 2.5 235 220 ? 2.5 220 220 table 46. lead-free process (from j-std-020d) package thickness (mm) package reflow temperature ( ?c) volume (mm 3 ) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 45 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus for further information on temperature profiles, refer to application note an10365 ?surface mount reflow soldering description? . msl: moisture sensitivity level fig 29. temperature profiles for large and small components 001aac844 temperature time minimum peak temperature = minimum soldering temperature maximum peak temperature = msl limit, damage level peak temperature
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 46 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 18. footprint information fig 30. footprint information for reflow soldering of sot1197-1 (hxson10) of PCF85063BTL sot1197-1 dimensions in mm footprint information for reflow soldering of dfn2626-10 package generic footprint pattern refer to the package outline drawing for actual layout by d slx sly gx gy hx hy 1.9 0.25 2.2 1.3 p 0.5 ay 3.05 2.5 2.85 2.85 3.3 spx spy 0.8 0.4 solder land plus solder paste occupied area solder land solder paste deposit solder resist dp gx gy hx hy spy sly by ay nspy nspx spx slx 0.025 0.025 sot1197-1_fr issue date 11-07-27 12-09-16
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 47 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 19. abbreviations table 47. abbreviations acronym description am ante meridiem bcd binary coded decimal cdm charged-device model cmos complementary metal oxide semiconductor esd electrostatic discharge hbm human body model ic integrated circuit lsb least significant bit msb most significant bit msl moisture sensitivity level pcb printed-circuit board pm post meridiem por power-on reset ram random access memory rtc real-time clock smd surface mount device spi serial peripheral interface
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 48 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 20. references [1] an10365 ? surface mount reflow soldering description [2] an10366 ? hvqfn application information [3] an11247 ? improved timekeeping accuracy with pcf85063, pcf8523 and pcf2123 using an external temperature sensor [4] iec 60134 ? rating systems for electronic tu bes and valves and analogous semiconductor devices [5] iec 61340-5 ? protection of electronic devices from electrostatic phenomena [6] ipc/jedec j-std-020 ? moisture/reflow sensitivity classification for nonhermetic solid state surface mount devices [7] jesd22-a114 ? electrostatic discharge (esd) sensitivity testing human body model (hbm) [8] jesd22-c101 ? field-induced charged-device model test method for electrostatic-discharge-withstand thresh olds of microelectronic components [9] jesd78 ? ic latch-up test [10] jesd625-a ? requirements for handling elec trostatic-discharge-sensitive (esds) devices [11] snv-fa-01-02 ? marking formats integrated circuits [12] um10569 ? store and transport requirements 21. revision history table 48. revision history document id release date data sheet status change notice supersedes PCF85063BTL v.2 20130415 product data sheet - PCF85063BTL v.1 modifications: ? adjusted block diagram ( figure 1 ) ? improved description of correction pulses ( ta b l e 1 4 and table 16 ) ? adjusted table 34 and section 8.6.3 ? enhanced application information ( figure 26 ) ? adjusted i dd and i li values ( ta b l e 4 2 ) ? adjusted spi-bus timing values ( table 43 ) PCF85063BTL v.1 20130123 objective data sheet - -
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 49 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 22. legal information 22.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 22.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 22.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such info rmation. nxp semiconductors takes no responsibility for the content in this document if provided by an information source outside of nxp semiconductors. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors and its suppliers accept no liability for inclusion and/or use of nxp semiconducto rs products in such equipment or applications and therefore such inclusion and/or use is at the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 50 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus export control ? this document as well as the item(s) described herein may be subject to export control regu lations. export might require a prior authorization from competent authorities. non-automotive qualified products ? unless this data sheet expressly states that this specific nxp semicon ductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liabili ty for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses t he product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors? warranty of the product for such automotive applicat ions, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors? specifications such use shall be solely at customer?s own risk, and (c) customer fully indemnifies nxp semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive app lications beyond nxp semiconductors? standard warranty and nxp semiconduct ors? product specifications. translations ? a non-english (translated) version of a document is for reference only. the english version shall prevail in case of any discrepancy between the translated and english versions. 22.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 23. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 51 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 24. tables table 1. ordering information . . . . . . . . . . . . . . . . . . . . .2 table 2. ordering options . . . . . . . . . . . . . . . . . . . . . . . . .2 table 3. marking codes . . . . . . . . . . . . . . . . . . . . . . . . . .2 table 4. pin description . . . . . . . . . . . . . . . . . . . . . . . . . .3 table 5. registers overview . . . . . . . . . . . . . . . . . . . . . .5 table 6. control_1 - contro l and status register 1 (address 00h) bit description . . . . . . . . . . . . . . .6 table 7. first increment of time circuits after stop bit release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 table 8. registers reset values . . . . . . . . . . . . . . . . . . . .9 table 9. control_2 - contro l and status register 2 (address 01h) bit description . . . . . . . . . . . . . .10 table 10. effect of bits mi and hmi on int generation . .12 table 11. clkout frequency selection . . . . . . . . . . . . .13 table 12. offset - offset register (address 02h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 table 13. offset values . . . . . . . . . . . . . . . . . . . . . . . . . .14 table 14. correction pulses for mode = 0 . . . . . . . . . . .15 table 15. effect of correction pulses on frequencies for mode = 0. . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 table 16. correction pulses for mode = 1 . . . . . . . . . . .16 table 17. effect of correction pulses on frequencies for mode = 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 table 18. ram_byte - 8-bit ram register (address 03h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . .18 table 19. seconds - seconds register (address 04h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 table 20. seconds coded in bcd format . . . . . . . . . . . .19 table 21. minutes - minutes register (address 05h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 table 22. hours - hours register (address 06h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 table 23. days - days register (address 07h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 table 24. weekdays - weekdays register (address 08h) bit description . . . . . . . . . . . . . . . . . . . . . . . . .20 table 25. weekday assignments . . . . . . . . . . . . . . . . . . .21 table 26. months - months register (address 09h) bit description . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 table 27. month assignments in bcd format . . . . . . . . . .21 table 28. years - years register (0ah) bit description. . . .22 table 29. second_alarm - second alarm register (address 0bh) bit description . . . . . . . . . . . . . .24 table 30. minute_alarm - minute alarm register (address 0ch) bit description . . . . . . . . . . . . . .24 table 31. hour_alarm - hour alarm register (address 0dh) bit description. . . . . . . . . . . . . . . . . . . . . .24 table 32. day_alarm - day alarm register (address 0eh) bit description . . . . . . . . . . . . . . . . . . . . . .25 table 33. weekday_alarm - weekday alarm register (address 0fh) bit description . . . . . . . . . . . . . .25 table 34. timer_value - timer value register (address 10h) bit description . . . . . . . . . . . . . .27 table 35. timer_mode - timer control register (address 11h) bit description . . . . . . . . . . . . . .27 table 36. timer clock frequency and timer durations. . . .28 table 37. first period delay for timer counter value t . . 29 table 38. int operation . . . . . . . . . . . . . . . . . . . . . . . . . . 29 table 39. serial interface . . . . . . . . . . . . . . . . . . . . . . . . 30 table 40. command byte definition . . . . . . . . . . . . . . . . 30 table 41. limiting values . . . . . . . . . . . . . . . . . . . . . . . . 32 table 42. static characteristics . . . . . . . . . . . . . . . . . . . . 33 table 43. spi-bus characteristics . . . . . . . . . . . . . . . . . . 38 table 44. carrier tape dimensions of PCF85063BTL . . . 42 table 45. snpb eutectic process (from j-std-020d) . . . 44 table 46. lead-free process (from j-std-020d) . . . . . . 44 table 47. abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 47 table 48. revision history . . . . . . . . . . . . . . . . . . . . . . . . 48
PCF85063BTL all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved. product data sheet rev. 2 ? 15 april 2013 52 of 53 nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus 25. figures fig 1. block diagram of PCF85063BTL . . . . . . . . . . . . . .2 fig 2. pin configuration for hxson10 (PCF85063BTL) .3 fig 3. handling address registers . . . . . . . . . . . . . . . . . .4 fig 4. stop bit functional diagram . . . . . . . . . . . . . . . . .7 fig 5. stop bit release timing . . . . . . . . . . . . . . . . . . . . .8 fig 6. software reset command . . . . . . . . . . . . . . . . . . . .9 fig 7. interrupt scheme . . . . . . . . . . . . . . . . . . . . . . . . . 11 fig 8. int example for mi . . . . . . . . . . . . . . . . . . . . . . .12 fig 9. offset calibration calculation workflow . . . . . . . . .17 fig 10. result of offset calibration . . . . . . . . . . . . . . . . . .18 fig 11. os flag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 fig 12. data flow for the time function . . . . . . . . . . . . . . .22 fig 13. access time for read/write operations . . . . . . . . .23 fig 14. alarm function block diagram. . . . . . . . . . . . . . . .26 fig 15. general countdown timer behavior . . . . . . . . . . .28 fig 16. data transfer overview . . . . . . . . . . . . . . . . . . . . .30 fig 17. spi-bus write example . . . . . . . . . . . . . . . . . . . . .31 fig 18. spi-bus read example . . . . . . . . . . . . . . . . . . . . .31 fig 19. device diode protection diagram of PCF85063BTL . . . . . . . . . . . . . . . . . . . . . . . . . . .32 fig 20. typical i dd with respect to f scl . . . . . . . . . . . . . .34 fig 21. typical i dd as a function of temperature . . . . . . .35 fig 22. typical i dd with respect to v dd . . . . . . . . . . . . . .36 fig 23. i dd with respect to quartz r s . . . . . . . . . . . . . . . .37 fig 24. oscillator frequency variation with respect to v dd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 fig 25. spi-bus timing . . . . . . . . . . . . . . . . . . . . . . . . . . .39 fig 26. application diagram for PCF85063BTL . . . . . . . .40 fig 27. package outline sot1197-1 (hxson10) of PCF85063BTL . . . . . . . . . . . . . . . . . . . . . . . . . . .41 fig 28. tape and reel details for PCF85063BTL . . . . . . .42 fig 29. temperature profiles for large and small components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 fig 30. footprint information for reflow soldering of sot1197-1 (hxson10) of PCF85063BTL . . . . .46
nxp semiconductors PCF85063BTL tiny real-time clock/calendar with alarm function and spi-bus ? nxp b.v. 2013. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 15 april 2013 document identifier: PCF85063BTL please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 26. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 4.1 ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 5 marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7 pinning information . . . . . . . . . . . . . . . . . . . . . . 3 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 8 functional description . . . . . . . . . . . . . . . . . . . 4 8.1 registers organization . . . . . . . . . . . . . . . . . . . 5 8.2 control registers . . . . . . . . . . . . . . . . . . . . . . . . 6 8.2.1 register control_1 . . . . . . . . . . . . . . . . . . . . . . 6 8.2.1.1 ext_test: external clock test mode . . . . . . . . 6 8.2.1.2 stop: stop bit function . . . . . . . . . . . . . . . . . 7 8.2.1.3 software reset. . . . . . . . . . . . . . . . . . . . . . . . . . 9 8.2.2 register control_2 . . . . . . . . . . . . . . . . . . . . . 10 8.2.2.1 alarm interrupt . . . . . . . . . . . . . . . . . . . . . . . . 11 8.2.2.2 mi and hmi: minute and half minute interrupt. 11 8.2.2.3 tf: timer flag . . . . . . . . . . . . . . . . . . . . . . . . . 12 8.2.2.4 cof[2:0]: clo ck output frequency . . . . . . . . . 12 8.2.3 register offset . . . . . . . . . . . . . . . . . . . . . . . . 13 8.2.3.1 correction when mode = 0 . . . . . . . . . . . . . . 15 8.2.3.2 correction when mode = 1 . . . . . . . . . . . . . . 16 8.2.3.3 offset calibration workflow . . . . . . . . . . . . . . . 17 8.2.4 register ram_byte . . . . . . . . . . . . . . . . . . . . 18 8.3 time and date registers . . . . . . . . . . . . . . . . . 18 8.3.1 register seconds . . . . . . . . . . . . . . . . . . . . . . 18 8.3.1.1 os flag: oscillator stop . . . . . . . . . . . . . . . . . . 19 8.3.2 register minutes. . . . . . . . . . . . . . . . . . . . . . . 20 8.3.3 register hours . . . . . . . . . . . . . . . . . . . . . . . . 20 8.3.4 register days . . . . . . . . . . . . . . . . . . . . . . . . . 20 8.3.5 register weekdays. . . . . . . . . . . . . . . . . . . . . 20 8.3.6 register months . . . . . . . . . . . . . . . . . . . . . . . 21 8.3.7 register years . . . . . . . . . . . . . . . . . . . . . . . . 22 8.4 setting and reading the time. . . . . . . . . . . . . . 22 8.5 alarm registers . . . . . . . . . . . . . . . . . . . . . . . . 24 8.5.1 register second_alarm . . . . . . . . . . . . . . . . . 24 8.5.2 register minute_alarm . . . . . . . . . . . . . . . . . . 24 8.5.3 register hour_alarm . . . . . . . . . . . . . . . . . . . 24 8.5.4 register day_alarm . . . . . . . . . . . . . . . . . . . . 25 8.5.5 register weekday_alarm . . . . . . . . . . . . . . . . 25 8.5.6 alarm function. . . . . . . . . . . . . . . . . . . . . . . . . 25 8.6 timer registers . . . . . . . . . . . . . . . . . . . . . . . . 27 8.6.1 register timer_value . . . . . . . . . . . . . . . . . . . 27 8.6.2 register timer_mode. . . . . . . . . . . . . . . . . . . 27 8.6.3 timer functions. . . . . . . . . . . . . . . . . . . . . . . . 27 8.6.3.1 countdown timer interrupts . . . . . . . . . . . . . . 29 9 characteristics of the spi-bus interface . . . . 30 10 internal circuitry . . . . . . . . . . . . . . . . . . . . . . . 32 11 limiting values . . . . . . . . . . . . . . . . . . . . . . . . 32 12 characteristics . . . . . . . . . . . . . . . . . . . . . . . . 33 13 application information . . . . . . . . . . . . . . . . . 40 14 package outline. . . . . . . . . . . . . . . . . . . . . . . . 41 15 handling information . . . . . . . . . . . . . . . . . . . 42 16 packing information . . . . . . . . . . . . . . . . . . . . 42 16.1 tape and reel information . . . . . . . . . . . . . . . 42 17 soldering of smd packages . . . . . . . . . . . . . . 43 17.1 introduction to soldering. . . . . . . . . . . . . . . . . 43 17.2 wave and reflow soldering. . . . . . . . . . . . . . . 43 17.3 wave soldering . . . . . . . . . . . . . . . . . . . . . . . 43 17.4 reflow soldering . . . . . . . . . . . . . . . . . . . . . . 44 18 footprint information . . . . . . . . . . . . . . . . . . . 46 19 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 47 20 references. . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 21 revision history . . . . . . . . . . . . . . . . . . . . . . . 48 22 legal information . . . . . . . . . . . . . . . . . . . . . . 49 22.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 49 22.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 22.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 49 22.4 trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 50 23 contact information . . . . . . . . . . . . . . . . . . . . 50 24 tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 25 figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 26 contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

▲Up To Search▲

Price & Availability of PCF85063BTL

	To Download PCF85063BTL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .